Dr. Evinrude

Specialist in
Evinrude Ficht & ETEC.

Dr. Evinrude, the specialist for buying, servicing or repairing Evinrude Ficht, ETEC or ETEC G2 outboards. 400 m² of service, showroom and experience center.

Johan de Konink, alias Dr. Evinrude, giving a thumbs up next to an Evinrude ETEC G2 outboard

What we do

From service to complete overhaul

From a small service to a complete overhaul of your Evinrude Ficht, ETEC or ETEC G2. With a passion for these engines, the best place for buying, servicing, repairs, overhauls, refurbishing, tuning and more.

Complete rebuild

We can strip down your powerhead and inspect the cylinders, crankshaft, bearings and pistons. In case of severe engine damage we can pull and replace cylinder liners in our powerhead oven. We neatly bore and hone the cylinders, and where needed we renew pistons, rings, bearings and gaskets. Then we rebuild your engine as good as new and tune it precisely.

Injectors & fuel system

We clean and test your injectors on our own test rig, built for the 40 or 55 volts Evinrude injectors need. We also check fuel pumps, lines and filters, so your engine runs clean and strong again.

EMM & electronics

We read out your engine with the original diagnostic software and test components according to the original service manuals. For EMM-related faults we are in close contact with hardwarecare.nl, the leading specialist in EMM repair.

Lower unit & drive

We can overhaul your lower unit after an accident, or replace seals, bearings and gears as a preventive measure. We work with the original BRP/OMC tools. We fill your lower unit with HPF Pro gearcase oil. That keeps your lower unit watertight and well lubricated, and prevents costly damage.

Cooling & water pump

Cooling is essential for your engine, but it certainly shouldn't run too cold either. We check that the impeller/water pump, thermostats and pressure relief valve work properly. Where needed we replace parts with original parts. That way your engine runs at the right operating temperature and performs at its best.

Service & winterising

We give your engine its annual service, prepare it for winter storage and get it ready for spring. That way it starts right away and runs at full power when the season begins.

Evinrude racing

Especially for racing boaters who want to go extra fast on the water, we configure custom-built Evinrude engines. You choose your colour, decals, powerhead and lower unit, and we build your engine entirely to your wishes. Tuning options are available, such as a race exhaust, power reeds and a modified lower unit with a low water pickup. With these engines you'll beat the competition.

White Evinrude race engine with red striping on a race boat on the waterGrey Evinrude ETEC HO with red striping on an engine standModified race lower unit in the spray boothEvinrude Ficht 250 race engine with silver race lower unitBlack Evinrude Direct Injection race engine with red striping and race lower unit

How we work

Four steps back on the water

  1. 01

    Contact

    Tell us which engine you have and what the problem is. Type (Ficht, ETEC or G2), year and horsepower already help us a lot.

  2. 02

    Diagnosis

    In the workshop we check the entire engine and read it out with diagnostic software. You get an honest answer about what the problem is and what it costs.

  3. 03

    Repair

    With know-how, patience and genuine parts we bring the engine back to top condition.

  4. 04

    Engine testing

    Every engine is test-run in the test tank or taken out on the water with our test boat. It is only done when everything is right.

In action

Take a look in the workshop

How to repair the magnets of an Evinrude flywheel with the repair kit: explained step by step in the workshop.

Watch on YouTube →

Spray booth

Refurbish

Engine cowls like new again in the professional spray booth.

Shop

Parts in stock

“A well-running ETEC outperforms any outboard on the lake.”

— Dr. Evinrude

About Dr. Evinrude

Only Evinrude, no other brands

From our workshop in Nij Beets, in the heart of the Frisian lake district in the Netherlands, we focus on one thing: Evinrude 2-stroke direct-injection engines, Ficht, ETEC G1 and ETEC G2.

That focus makes the difference. Thanks to our extensive experience we know exactly how to get these engines running at their best and, when needed, how to repair them.

Don't believe the rumours: Ficht and ETEC are not engines to stay away from. Parts are readily available, often better than for other brands, and a properly running Evinrude easily outperforms any other outboard on the water.

  • ✓Honest advice up front
  • ✓Quality parts
  • ✓Test-run before delivery
  • ✓Ficht, ETEC and ETEC G2
More about us →

A question about your engine?

Share your question, photos and videos via WhatsApp. That way we can see right away what is going on and help you quickly.

Send a WhatsApp @evinrude

Contact

Book your engine

Tell us about your engine and what is wrong with it. We will get back to you as soon as possible with advice or an appointment.

Dr. Evinrude

Swynswei 2D-1
9245 HE Nij Beets
The Netherlands

Workshop visits by appointment

See us on Facebook